Sloan's Woodshop - The Scroll Saw Store

Home

Plywood

Scroll Saw Blades

Band Saw Blades

Clock Inserts

Acrylic Sheets

Scroll Sanders & SS Files

Drum Sander

Pattern Books

Patterns

Drill Bits

Forstner Bits

Router Bits

Brush Sets

Miscellaneous

Needle Files & Riffler Sets

Web Specials

Ordering Info

Contact Us

Adding Relief Cuts to Tight Fretwork Corners

Tight corners give fretwork its crisp, lace-like character, but they are also where a scroll saw is most likely to snag, wander or chip the finished edge. A relief cut solves this by removing a small, deliberate section of waste so the blade has room to change direction. Done well, the extra cut disappears into material that will be discarded, leaving a clean corner and a predictable cutting path.

Relief cuts are useful when transferring a pattern to a different plywood thickness, adapting a template or working with a finer blade than the original design allowed. They are not a substitute for a sound cutting path or a steady machine. The essential skill is deciding where the blade needs space, marking that space on the waste side, and keeping the alteration small enough for the finished panel.

Why tight corners snag on a scroll saw

A scroll saw blade is thin, but its kerf still occupies space. On a straight cut, the teeth enter and leave the sheet without obstruction. At a tight inside corner, the finished edge lies close to the turning path, and the blade must pivot while its full width is still in the wood. Without enough clearance, the blade is pushed sideways, the teeth drag, or the corner splits.

That sideways pressure is often called blade tracking, although tracking problems can also come from a worn guide, incorrect tension or a blade that has been bent. A relief cut addresses the geometry of the corner, not every cause of a poor cut. It gives the blade a short route through waste, allowing the pivot to happen before the saw reaches the finished wall.

Not every corner needs the same treatment. A broad inside radius can accommodate the blade without relief, while a needle-sharp turn may need a small notch or a wider radius. On decorative fretwork, the smallest surviving gap still has to look intentional, so a cut that solves the sawing problem can spoil the design if it is too large.

Plan the relief area before cutting

Make a full-size test on an offcut of the same thickness before cutting the finished sheet. Draw the proposed corner shape, mark the waste side and try the blade you intend to use. Measure in millimetres: Australian plywood and hobby timber are normally sold in metric sizes, while American patterns and tool listings often use inches. Converting early prevents a corner opening from shrinking unexpectedly during transfer.

The relief area should open the turn without removing material from the finished side. A small triangular notch, stepped cut or generous internal radius can work; the choice depends on the blade kerf, tooth width and the scale of the pattern. Test cuts are essential because a small change in blade thickness can affect a delicate point, and a notch that suits a full-size panel may overwhelm jewellery-scale fretwork.

Trace the template rather than relying on a sketch copied freehand. Use graphite paper or a fine pencil, label the waste area lightly, and note the grain direction and the face that must stay clean. Quilting is another natural source of stepped angles and repeated curves. Australian makers browsing quilting supplies can use familiar block geometry as visual references, then simplify the lines for a scroll saw rather than attempting to copy an entire quilt design.

Make the cut without fighting the blade

Set up the machine on a stable, level bench with the work supported close to the table. Clamp the sheet securely, keep fingers well away from the teeth, and wear eye protection while directing extraction. Dust collection matters in the compact garages and apartment hobby rooms common around Melbourne, Brisbane and Sydney, where a small saw may share the space with other weekend projects.

Check the saw’s electrical setup as carefully as its blade. Australian mains is nominally 230 V, so confirm the voltage rating on a second-hand machine rather than relying on a plug adaptor. Look for an undamaged Australian Type I plug, sound insulation and guards fitted according to the manufacturer’s instructions, and check the applicable AS/NZS 60335 requirements for electric woodworking tools. A protected RCD circuit is important in a home workshop. Disconnect the saw before changing a blade or clearing a workpiece.

For an internal opening, drill a pilot hole through the waste, using a scrap backing to limit tear-out, and join it to the pattern with the saw. Approach the corner slowly, stop just before the turn, and make the relief cut while the blade has room in the waste. Ease into the outgoing line, then support the offcut so its weight does not pull the blade sideways.

If the blade catches, release the foot control and let it stop before changing the cut. Do not force a bent blade back onto the line; replace it and re-enter from a clean direction. Fine feed pressure reduces jagged teeth marks, while keeping the blade moving prevents burning in dense plywood. Support the work with the table, a roller or a sacrificial foam board, but keep fingers out of the blade’s vertical path.

Match the blade to the material

Blade choice controls how easily the saw can turn. Fine-tooth, thin blades suit narrow curves in thin plywood and small decorative parts, while a sturdier scroll saw blade with fewer teeth can cut thicker stock more steadily. Skip-tooth blades are useful for hardwood and straight runs, but they may wander at a tight corner. Match the blade width, thickness and tooth count to the machine’s capacity rather than selecting by the material name alone.

For a US-based comparison of available styles and sizes, the scroll saw blades catalogue at Sloan’s Woodshop in Lebanon, Tennessee is a phone-order reference. Its stated shipping area is within the United States, so Australian buyers should treat it as a product reference unless dispatch is confirmed, or source the same blade specification from a local timber merchant or specialist woodworking supplier.

Material preparation is just as important as the tooth. Sand plywood faces lightly if the pattern requires a very fine edge, and support thin sheet so it does not flex away from the table. Keep spare blades in a dry case, note the relevant tooth count and thickness, and discard a blade as soon as it bends or loses its tracking. For an imported order, check dispatch, insurance, GST and any Australian Border Force requirements before paying.

A shop-floor workflow for cleaner corners

Australian hobby woodworkers often buy replacement blades from a national hardware chain, an independent timber merchant or a specialist supplier, so check local stock before committing to an overseas purchase. A practical home setup also has to accommodate Australian workshop habits: limited bench space, occasional weekend cutting sessions and the need to keep a rented garage or shared hobby room tidy. A labelled offcut box for each blade and thickness turns testing into a repeatable habit rather than a discarded pile.

Community classes, makerspaces and craft-market projects provide useful ways to compare templates and learn how a particular saw handles plywood. Cutting and sanding produce fine dust, so allow time for extraction and clean the machine before switching from plywood to hardwood. Files and sanding blocks can refine a small relief notch, but the aim is to conceal the notch within the waste edge, not to enlarge the opening after the panel is finished.

  • Cut a full-scale corner test on offcut plywood of the same thickness, then mark the waste side before committing to the finished pattern.
  • Make the relief opening slightly wider than the blade kerf, then adjust its length from actual test cuts rather than a fixed rule.
  • Use a sacrificial backing beneath thin plywood and drill internal waste openings with a sharp bit smaller than the finished space.
  • Keep the blade at its recommended speed, feed the work slowly and guide the sheet through turns rather than twisting the blade.
  • Replace any blade that bends or tracks poorly; fresh, correctly tensioned blades usually make relief cuts easier than forcing a tired one.
  • Record blade thickness, tooth count and material in a small workshop log, then reuse the successful setup for matching panels.

Home Plywood Scroll Saw Blades Band Saw Blades Drill Bits Forstner Bits Router Bits Clocks Acrylic Sheets Pattern Books Misc

Drum Sander Kit Scroll Sanders & Files Brush Sets Needle File & Riffler Sets Web Specials Scroll Saw Patterns Contact Us Ordering

Order Toll Free:  1-888-615-9663

Sloan's Woodshop - 3453 Callis Road - Lebanon, TN 37090

We Do Not Ship Outside of the US