Sloan's Woodshop - The Scroll Saw Store

Home

Plywood

Scroll Saw Blades

Band Saw Blades

Clock Inserts

Acrylic Sheets

Scroll Sanders & SS Files

Drum Sander

Pattern Books

Patterns

Drill Bits

Forstner Bits

Router Bits

Brush Sets

Miscellaneous

Needle Files & Riffler Sets

Web Specials

Ordering Info

Contact Us

Adjusting a bandsaw table for accurate bevel cuts

A bandsaw can produce clean, repeatable bevels when the table, blade and fence work together. The adjustment itself is simple: loosen the table hardware, tilt the table to the required angle, then lock it firmly. Accuracy depends on the checks made before and after that movement.

For Australian woodworkers, the same method applies whether the project is made from radiata pine, jarrah, Victorian ash or recycled hardwood. A compact hobby saw in a suburban shed needs the same care as a larger machine in a professional workshop, especially when a sloping cut will later be joined, glued or used as a visible edge.

Understand what the angle means

Bandsaw tables usually tilt away from the blade to create a bevel. The scale on the trunnion may show the table’s angle from its normal 90-degree position, while a drawing or project plan may describe the angle on the finished workpiece. These two descriptions can cause confusion, so check which reference the plan uses.

For example, a table tilted 20 degrees from its square position produces a cut face that is 20 degrees away from a cut made at 90 degrees to the table. If a design specifies a 20-degree bevel from the face of the timber, the required machine setting may be different. Make a small sketch showing the finished angle before touching the adjustment.

The table should normally be square to the blade when the scale reads zero. Use the machine’s positive stop or adjustment bolt to establish this reference. Do not assume the printed scale is exact; scales can shift, become hard to read or vary between bandsaw models.

Prepare the machine before tilting

Disconnect the power before checking the blade, table slot or guides. Confirm that the blade is correctly tensioned, tracking in the centre of the wheel tyres and suitable for the timber. A coarse blade with too few teeth can tear small workpieces, while an excessively fine blade may struggle in thick stock and wander during the cut.

Set the upper blade guide close to the workpiece without restricting movement. The side guides and thrust bearing should support the blade without pressing against it during free running. Clean sawdust from the table and trunnion surfaces, since a chip trapped beneath the table can alter the angle or prevent it from sitting securely.

Before bevel cutting, inspect the blade for damaged teeth, a kinked back or excessive residue. Australian hardwoods can be dense and abrasive, and resinous softwoods may leave deposits on the blade. Suitable replacement blades and related workshop supplies can be found through Sloan's Woodshop, which catalogues bandsaw blades, sanding products and other woodworking accessories.

Set and verify the table angle

Release the table locks just enough for the table to move. On many saws, loosening the knobs fully allows the table to shift suddenly, so support it with one hand while adjusting the trunnion. Move it slowly towards the required setting, keeping fingers clear of the blade and table opening.

Use the built-in scale only as a starting point. Place a reliable bevel gauge, digital angle gauge or combination square on the table, depending on the angle being measured. A digital gauge can be zeroed on the table surface before the table is tilted, but check that the magnet or base is sitting on a clean, flat area rather than on a raised rib.

Tighten the table locks gradually and recheck the setting. Some tables move a degree or two as the knobs are tightened. If the table has a 90-degree stop, confirm the square setting with a machinist’s square against the blade, not against the side of the blade teeth. The teeth can project unevenly and give a false reading.

Account for the blade and fence

A bevel cut changes the relationship between the timber, blade and fence. If the fence remains parallel to the table slot while the table is tilted, the workpiece may not sit naturally against it. On some saws, the fence must be repositioned so its face supports the timber throughout the cut.

Test the arrangement with the saw switched off. Place scrap timber on the table and slide it towards the blade, observing whether the piece contacts the fence evenly. If the stock rocks, catches on the blade opening or tends to lift, correct the fence position before starting the machine.

For narrow pieces, a tall auxiliary fence can provide better support. A featherboard may also help, but it must be positioned so it does not force the workpiece sideways into the blade. Never use a hand position that places fingers in line with the cutting path. A push stick, small handle or purpose-made jig is worthwhile for short or awkward pieces.

A tilted table also changes the clearance around the blade guard and insert. Check that the blade can move freely through the throat plate and that the guard still sits close to the work. If the standard insert leaves a wide gap at the new angle, use a suitable zero-clearance insert designed for the machine rather than filling the opening with loose material.

Make a test cut and refine the result

Use a piece of the same species and similar thickness as the final work. Mark the waste side clearly, since a bevel can make it less obvious which edge should remain. Feed the test piece steadily without forcing it; pushing too hard can bend the blade and make the cut appear to have the wrong angle.

After cutting, check the bevel with the same tool used to set the table. A digital gauge is convenient for comparing the cut face, while a bevel gauge and protractor can work well for traditional layouts. Check both ends of the cut. If the angle differs along the length, the blade may be wandering, the timber may be twisting or the feed pressure may be uneven.

When the angle is close but not exact, make small adjustments rather than moving the table by a large amount. If the cut is consistently too steep, reduce the table tilt slightly; if it is too shallow, increase it. Record the final machine setting in a notebook, including the blade width, timber species and stock thickness.

This habit is especially useful when moving between readily available Australian timbers. A soft radiata pine offcut may behave smoothly, while spotted gum, blackwood or jarrah can expose blade drift that was not visible in the test material. The same scale reading does not guarantee the same cutting behaviour.

Control drift, feed rate and surface quality

Blade drift is the tendency of the blade to move away from the intended line as timber is fed. It is affected by blade geometry, tension, sharpness and the way the blade is tracking. When drift is present, align the fence to the blade’s actual cutting path rather than assuming it is parallel to the table slot.

A simple drift test involves cutting part-way through scrap while following a straight line without using the fence. Stop the machine, keep the timber in position and mark the angle of the stock relative to the table. The fence can then be adjusted to match that natural direction. This is more reliable than trying to force every blade to follow a fixed alignment.

Feed the timber at a steady pace that allows the teeth to clear sawdust. Burning, squealing or a polished dark line on the cut surface usually indicates a dull blade, an unsuitable tooth pattern or excessive pressure. A rough cut may also result from turning the workpiece too sharply, which twists the blade and increases the bevel error.

For long boards, support the stock with an outfeed table or roller stand. A board that drops at the end of a cut can pull the timber sideways and spoil the final section. In a small garage or shed, make sure the support is stable on the floor and does not obstruct a safe retreat from the machine.

Finish the setup for repeatable work

Once the test cut is correct, mark the table setting or note the angle in the project record. Some woodworkers use a small reference block cut at the required angle so the setup can be checked quickly during a longer session. The block should be labelled and stored where it will not be mistaken for scrap.

Plan the order of operations before cutting finished parts. Beveling can remove a reference edge, so complete layout marks and any cuts that rely on a square face first. If several components must match, cut them with the same blade and setup, using a stop block or template where appropriate rather than measuring each part independently.

Small decorative projects often depend on accurate compound-looking edges even when only a single table tilt is used. A miniature display piece, such as one inspired by miniature bottle ideas, may require tiny bevels that are difficult to hold by hand. In such cases, a secure jig and oversized blank are safer than trying to guide a very small finished part directly past the blade.

After the work is complete, return the table to its square position if the machine will be used for general cutting. Brush away dust, release or reduce blade tension according to the manufacturer’s instructions, and check the locks before the next session. A clean, square reference setting makes the following bevel adjustment faster and more dependable.

Home Plywood Scroll Saw Blades Band Saw Blades Drill Bits Forstner Bits Router Bits Clocks Acrylic Sheets Pattern Books Misc

Drum Sander Kit Scroll Sanders & Files Brush Sets Needle File & Riffler Sets Web Specials Scroll Saw Patterns Contact Us Ordering

Order Toll Free:  1-888-615-9663

Sloan's Woodshop - 3453 Callis Road - Lebanon, TN 37090

We Do Not Ship Outside of the US