Sloan's Woodshop - The Scroll Saw Store

Home

Plywood

Scroll Saw Blades

Band Saw Blades

Clock Inserts

Acrylic Sheets

Scroll Sanders & SS Files

Drum Sander

Pattern Books

Patterns

Drill Bits

Forstner Bits

Router Bits

Brush Sets

Miscellaneous

Needle Files & Riffler Sets

Web Specials

Ordering Info

Contact Us

Choosing a Forstner bit for flat bottom holes in wood

A Forstner bit is designed to bore a hole with a flat floor and clean, nearly straight sides in wood. Its broad cutting wings remove material across the width of the bit, while the centre cutting edge or pilot point locates the hole. That geometry makes it useful for dowel holes, pegs, hardware recesses and other joints where a twist drill would leave a conical bottom.

The right choice depends on hole diameter, timber density, the size and shape of your drill, and how much accuracy the joint requires. A sharp, well-centred bit can produce neat flat bottom holes in project plywood or furniture timber, while a damaged or unsuitable bit may wander, burn the wood or leave a rough, uneven base. Choose for the work rather than simply for the largest diameter in the drawer.

What a Forstner bit actually cuts

A Forstner bit differs from a twist drill in the way it removes material. The twist drill produces a cone-shaped hole because its flutes cut inward toward the point; the Forstner has cutting wings at the perimeter and often a centre-cutting edge that shaves the base flat. It is therefore a sensible choice when the bottom must seat squarely against a dowel, pin, tenon or hardware fitting.

Pay attention to the centre, though. A brad point helps the bit start in a marked position, whereas a centre-cutting edge is what forms the floor; some designs combine the two. Quality also affects wall accuracy, chip flow and how easily the bit stays centred. A well-made bit with balanced cutting geometry is usually worth favouring over a very cheap, visibly coarse one for visible joinery.

Matching diameter to timber and the joint

Start with the diameter required by the finished component rather than the size of the timber. Measure the dowel, bolt, screw or insert, then apply only the clearance specified by its manufacturer. Australian furniture and joinery often use 6, 8, 10 and 12 mm dowels, while imported fittings may call for 1/4, 5/16 or 3/8 inch holes. A bit that is fractionally undersize can make assembly difficult; an oversize hole weakens the joint and leaves visible gaps.

Timber changes the result. Radiata and hoop pine are forgiving and inexpensive for utility work, though sharp edges can still raise long fibres around the rim. Jarrah, meranti and spotted gum are harder and may be more resinous, demanding a keen cutter and slower, controlled feeds. Test each combination on an offcut of the same species, especially when the hole appears on a show face. A scrap backing piece below the work helps prevent breakout from the reverse side.

Fitting the bit to your drill safely

Check the shank before the cutting head. Most Forstner bits have a 6.35 mm, or 1/4 inch, shank even when the head is much wider, while larger versions may use a 5/8 inch shank or a separate arbor. Chuck capacity refers to the shank, not the diameter of the hole being cut. Many Australian drill presses use a 13 mm chuck, so confirm that its jaws can clamp a 1/4 inch shank securely; a larger shank may need a different chuck. A drill press gives the most repeatable alignment for square, accurately sized bores.

Speed and feed should follow the bit maker's guidance, not an assumed twist-drill setting. Large cutters work best at lower spindle speeds, and Australian mains-powered drill presses are commonly 240 V, so check the machine's label and manual rather than copying a setting from an overseas 120 V tool. Firm, even pressure lets the cutter work; forcing it can deflect the bit or overload the spindle. Clean swarf and dust from the chuck and collet before fitting the bit; the shop's guidance on collet care tips is aimed at routers, but the same checks help prevent a bit from running eccentric.

Set depth with the machine's stop where possible. The relevant measurement is from the cutting edge to the intended floor, not simply from the drill chuck to the work surface. On a handheld drill, mark the bit with tape or pencil, but allow for the different projection of the centre point and cutting wings. Test on waste before trusting the setting in a finished component.

Drilling a clean flat-bottomed bore

Clamp the workpiece securely and support it without lifting it away from the drill-press table. Mark the centre with a fine awl or knife, then add a sacrificial board beneath the work if there is any risk of breaking through. Check that the bit is square to the face and that the marked point sits directly under the spindle. A centre punch is useful for a pilot-point bit, but excessive hammering can split the timber.

Bring the spinning cutter to the mark and allow the centre to engage before applying strong feed pressure. On a handheld drill, use a steady trigger and keep the tool aligned with both hands; short taps tend to make the bit wander. Increase feed smoothly as the wings enter the wood. If the tool grabs, release pressure without yanking it away, let the bit stop, clear the cut and approach again at a controlled rate.

Watch the chips and the sound. Healthy Forstner cutting produces small, even chips and a clear, quiet cutting edge. Fine dust or smoke means the cutter is rubbing rather than slicing, often because the feed is too slow, the bit is blunt or resin is building up. Stop exactly at the set depth and withdraw without driving the centre through the underside. For a truly square base, choose a centre-cutting design and verify its actual finish on the test piece.

Keeping edges sharp and diagnosing rough holes

Resin and softwood sap collect around Forstner cutting edges and can quickly spoil an otherwise clean bore. Brush chips away during the cut, then wipe the bit after use and store it dry. Inspect the perimeter wings and centre edge for nicks, especially after hitting a screw or knot. Small damage can sometimes be corrected with a fine file or suitable sharpening system, but severe chipping or a bent shank calls for replacement. Grinding away too much metal can upset the cutter balance and make it run eccentric.

If a hole wanders, check the bit's sharpness, the marked centre, chuck runout and the angle of the drill before blaming the timber. Rough walls usually indicate a dull edge, excessive feed pressure or poor chip clearance, while an uneven floor can come from a bent bit, debris at the bottom or an inaccurate depth stop. Burn marks and smoke point to excessive speed, too little feed in resinous wood or a dirty cutter. Correcting the underlying cause is quicker and more reliable than trying to hide the defect with filler.

A practical buying checklist for Australian workshops

Sloan's Woodshop is a catalogue-led specialty retailer based in Lebanon, Tennessee. Its site provides information on bits, blades and craft accessories and directs orders through a toll-free telephone line rather than online checkout, with published shipping within the United States. The catalogue can still be useful for checking cutter types and dimensions, but Australian buyers should confirm freight, currency, GST and delivery arrangements before attempting a purchase, or source an equivalent locally.

For a local purchase, compare the metric diameter and shank with the fitting and drill, then read any speed limits. Specialist timber and tool suppliers around Melbourne, Brisbane, Sydney, Adelaide and Perth are an important part of the Australian market, and many stock common imperial Forstner sizes as well as metric dowel dimensions. Check the return policy on a sharpened or fitted bit, and buy from a supplier that can confirm whether its centre geometry leaves a flat floor.

  • Choose the finished hole diameter from the fitting, allowing only the clearance its maker specifies.
  • Match the shank to the chuck and confirm the cutter head is suitable for the machine's capacity.
  • Select a centre-cutting design when the joint requires a genuinely square floor.
  • Follow the maker's spindle-speed guidance and use a steady feed suited to the timber.
  • Set a repeatable depth stop and mark the centre before boring.
  • Remove chips frequently, clean the edges after use and store the bit dry.

Record both metric and imperial sizes on the job sheet, especially when an old cabinet, imported fitting or offcut has no dimensions written on it. In Aussie joinery, that simple check prevents the common mismatch between a metric dowel and an imperial catalogue bit. A sharp, correctly sized Forstner held square and stopped at a measured depth is the surest route to a repeatable flat-bottomed hole.

Home Plywood Scroll Saw Blades Band Saw Blades Drill Bits Forstner Bits Router Bits Clocks Acrylic Sheets Pattern Books Misc

Drum Sander Kit Scroll Sanders & Files Brush Sets Needle File & Riffler Sets Web Specials Scroll Saw Patterns Contact Us Ordering

Order Toll Free:  1-888-615-9663

Sloan's Woodshop - 3453 Callis Road - Lebanon, TN 37090

We Do Not Ship Outside of the US