Sloan's Woodshop - The Scroll Saw Store |
Choosing a router bit for plywood finger jointsChoosing a router bit for cutting finger joints in plywood boxes comes down to making a narrow, repeatable slot whose width matches the panel. The finished joint depends less on a decorative profile than on three things: the bit's cutting geometry, the accuracy of the jig and the condition of the plywood edge. A round-over or V-bit may look tempting in a box, but neither creates the square-bottomed recess required by an interlocking finger joint. Most makers start by routing open slots from panel ends, then assemble tabs from the adjoining panels. That means a straight, sharp cutter is the practical default, with the panel thickness determining the required cut width. The box may use 9, 12, 15, 17 or 18 mm plywood, so measure the actual sheet rather than trusting the nominal label. In Australia, shank systems, 240 V tools and local stock sizes also need checking before a bit is bought or imported. Why a straight-cutting bit suits finger jointsA finger joint is essentially a sequence of rectangular notches. Each notch must have parallel sides, a clean floor and enough clearance for the mating tab, normally the thickness of the sheet itself. A straight-cutting router bit produces that geometry directly when its diameter equals the intended slot width. It also cuts fast because the chip has a clear path through the full depth of the plywood. Router bits with a bearing can be useful when the cut is referenced to the panel face, but the bearing should guide a slot, not create a rounded corner. For production boxes, plunge or straight bits in a purpose-made fence or indexing jig usually give more control. The alternative is a dado-style setup on a table saw, which is faster for batches but needs careful alignment and creates a very different dust and kickback risk. Match the cutter to the plywoodMeasure at three places along each edge because plywood can vary slightly, then make a test offcut with the same face veneer and edge treatment. Mark the slot width, depth and spacing before tightening the workpiece. The cutter diameter should normally match the plywood thickness, but the physical test matters more than the nominal dimension. For example, a sheet sold as 12 mm plywood may need a little hand adjustment if it is tight, whereas a slightly undersized slot will leave a loose joint. Planning the geometry before the router is switched on can prevent ruined panels. The woodworking project plans collection is useful as a source of scale and shape ideas, including small craft forms that show how tabs and slots relate visually. Apply those proportions to the box rather than copying dimensions blindly, and add a dry-fit allowance at the corners. If the project also needs a scroll-sawed lid or decorative grille, separate that operation so the box panels remain flat and square. Flute, bearing and shank considerationsCarbide is usually the better material for plywood because it stays sharper in resinous or faced veneer and tolerates occasional abrasive fibres. A two-flute straight bit removes material quickly and works well in clean hardwood; a four-flute design generally gives a smoother finish but produces smaller chips and more heat. For edge-visible slots, an upcut, downcut or compression spiral can improve chip control, provided the chosen rotation, feed direction and fixture suit the bit. Collet size is another hard limit. Many Australian routers use a 6 mm collet, while common workshop routers in the United States often use 6.35 mm, or 1/4 inch. Some machines accept both with suitable collets and bushings, but a 6.35 mm shank must never be forced into a 6 mm collet. Check the router manual and measure the shank before purchase. This is especially important for buyers comparing a US bit catalogue with equipment used in Sydney, Melbourne, Brisbane or Adelaide. Build a repeatable routing setupA router square in the hand is not square enough for box making. Build or borrow an indexing fence from scrap plywood, clamp the workpiece against a fixed stop and mark each slot from a measured baseline. Alternatively, use a plunge bit with a template and a guide bushing, checking that the template accounts for both the cutter and bushing diameters. Hold-down clamps should pull the panel toward the fence without distorting it. Cut in several shallow passes when the slot depth exceeds the bit's useful cutting height. Increase depth gradually, clean the chips between passes and let the cutter reach full speed before entering the plywood. On a finger-jointed box, consistency matters more than speed: one deep pass can wander, scorch the face veneer or pull the workpiece loose. A sacrificial support beneath a narrow panel keeps the exit chip from striking the bench. Control tearout and test the jointPlywood often splits along its outer layers when a router enters at the end grain. Reduce that risk with a sharp compression or downshear bit, light scoring passes, and proper support close to the cut. A full-width sacrificial backing board can also prevent breakout. If the slot lies only a few millimetres from the edge, clamp carefully, hold the router firmly and expect to refine the edge with a file or sandpaper after routing. Small parts expose router weaknesses more clearly than large panels. The detailed wooden music box guide demonstrates the value of controlled cutting on decorative wooden projects, although its scroll-saw methods are most appropriate for curved outlines and intricate profiles. For square finger joints, a router makes the repeated slots quickly; the same disciplined layout, clean supports and trial pieces transfer directly to that work. Before routing the full set, assemble two or three test tabs in the matching slots and check the fit around a temporary frame. The fit should pull the joint closed without forcing it, while still leaving a fine glue line. If the panels meet at a mitred corner, make the tabs slightly less deep so the outer faces can be brought flush without chipping the veneer. Compare options before orderingOnce the joint has been proved on offcuts, compare bits by the job rather than by the size of the box. A small decorative box may suit a compact 6 mm shank, while a stack of larger panels rewards a stiffer cutter and a better fixture. Review the full range of plywood, router bits, sanding tools and project accessories at Sloan's Woodshop before deciding.
Sloan's Woodshop operates as a catalogue and sends customers to a toll-free phone line rather than offering online checkout. Its stated shipping area is within the United States, so Australian buyers should not assume a US order will arrive in Australia. Ask about availability, cutter dimensions and shipping before paying, and compare the total landed cost with local stock rather than focusing only on the advertised bit price. For practical purchasing, Bunnings and specialist Australian woodworking suppliers are useful comparison points for common 6 mm shank bits and locally stocked plywood. Imports bought through a courier or freight forwarder may attract GST and any applicable customs duty, with the final charge depending on the product code and clearance method. Within Australia, sellers in Brisbane or Perth may face higher inbound freight costs than buyers in Melbourne or Sydney, so confirm currency, delivery insurance and return terms before placing the order. |
|
Home Plywood Scroll Saw Blades Band Saw Blades Drill Bits Forstner Bits Router Bits Clocks Acrylic Sheets Pattern Books Misc Drum Sander Kit Scroll Sanders & Files Brush Sets Needle File & Riffler Sets Web Specials Scroll Saw Patterns Contact Us Ordering Order Toll Free: 1-888-615-9663 Sloan's Woodshop - 3453 Callis Road - Lebanon, TN 37090 We Do Not Ship Outside of the US |