Sloan's Woodshop - The Scroll Saw Store

Home

Plywood

Scroll Saw Blades

Band Saw Blades

Clock Inserts

Acrylic Sheets

Scroll Sanders & SS Files

Drum Sander

Pattern Books

Patterns

Drill Bits

Forstner Bits

Router Bits

Brush Sets

Miscellaneous

Needle Files & Riffler Sets

Web Specials

Ordering Info

Contact Us

Cleaning a dull router bit with a diamond sharpening stone

Router bits rarely go from sharp to useless in one cut. Resin and sawdust build up on the flutes, a clean edge starts to tear timber, and the router develops a harsh note that can be mistaken for a bearing problem. Cleaning a dull router bit with a diamond sharpening stone can recover an intact but blunt edge. It cannot rebuild chipped carbide, repair a cracked shank, or restore an edge that has already been ground away.

Sloan's Woodshop in Lebanon, Tennessee, is a specialty catalogue for scroll-saw and woodworking supplies, including router bits, saw blades, files, and abrasives. Its staff assist with product selection through a toll-free phone order, and fulfilment is within the United States. Australian buyers should therefore use the catalogue as a product reference and check local suppliers for an equivalent stone and spare bits. The sharpening process is not region-specific, although Australian routers normally run on 230–240 volts, so a 120-volt North American machine must never be connected to local power.

Recognise when the router bit needs attention

Start by separating dirt from damage. Remove the cutter from the router, brush away loose sawdust, and examine the cutting edges under bright light. A continuous edge carrying a fine grey burr or rounded shine can often be cleaned and honed. Deep nicks, a missing corner, or a visibly cracked carbide tip call for replacement. Rotate the bit by hand while inspecting it; if one flute is damaged, the router may still cut but will load unevenly and stress the arbor.

Next, identify the material and geometry. HSS has a steel body and can tolerate more conventional abrasion, while carbide-tipped cutters need a gentler, more precise approach. Two-flute straight bits and many hollow-ground bits are sharpenable; spiral compression cutters usually are not. Australians often use the same shed for scroll sawing, cricket-net repairs, and other weekend projects. A specialist such as Castanos Sport represents the sporting side of that broad hobby market, while a woodworking supplier is the relevant source for cutter geometry and matched replacements.

Choose a diamond stone for the job

A diamond sharpening stone uses industrial diamond grit bonded to a rigid plate, so it removes metal more efficiently than an ordinary oilstone, especially on carbide. Match the grade to the job: roughly 120–300 grit for a badly rounded but intact edge, 300–600 for routine correction, and 800–1500 for refining the bevel. Exact grit systems vary between manufacturers. A finer plate or diamond paste can finish the edge after the burr has been raised and removed.

For most Australian home workshops, a stable two-sided plate around 400/1200 grit is a versatile starting point. Shops such as Bunnings, specialist sellers such as Total Tools, and established online marketplaces such as eBay Australia are practical places to compare products. Check whether the plate must be used wet, oiled, or dry; a metal-bonded stone is not the same as a waterstone. Also record the bit diameter and shank size, since Australian catalogues commonly list both metric and imperial sizes even when the cutter itself comes from the United States.

Set up a safe and stable workspace

Sharpening is safer and more accurate with the router disconnected. Remove the bit completely rather than trying to work around an installed cutter, secure the stone flat on the bench, and wear eye protection. Keep loose gloves, jewellery, and sleeves away from the cutting edge, and use a bench hook or simple jig to support the bit. Do not hold the edge directly between your fingers, even when applying only light pressure.

A spare corner of a mates' shed can be enough, provided the bench will not rock. A firm bench hook, a small machinist's vice, or a purpose-made router-bit guide gives the cutter a repeatable position. Before adapting a scroll-saw bench into a sharpening corner, the scroll-saw workbench guide from Sloan's Woodshop is a useful check on clamp clearance and bench height. The same advice applies in a verandah workshop in Brisbane or a converted Perth garage: use a solid, level surface and keep stone grit away from the saw.

Before touching the bit, clean the stone. Wash a water-compatible plate with detergent, rinse it, and dry it fully; use the manufacturer's oil method for a metal-bonded plate. Check that it is flat by drawing a straightedge across the surface and looking for light beneath the edge. A hollow or deeply grooved diamond plate will produce an uneven bevel, so dress a light groove or replace a badly worn stone. Brush stone dust away before each grit change.

Restore the cutting edge by hand

Degrease the cutting faces with a suitable tool cleaner and let them dry fully. Then mark each face with a fine permanent marker so the original geometry remains visible. A bright line that disappears evenly shows where the stone is contacting; a patchy line reveals a tilt or a bad setup. Preserve the manufacturer's bevel angle and relief rather than forcing every bit into a generic 45-degree angle. A commercial jig, an adjustable protractor, or a carefully made guide helps, particularly on hollow-ground bits where the back of the flute is already curved.

Start with the grit chosen for the condition and make light, controlled passes across the marked face. Use the bit shank or a jig as a handle, moving the cutter in a smooth arc while changing its angle gradually. Rotate the tool regularly so the whole bevel is contacted, then alternate flutes to preserve symmetry. Pause often to brush away swarf and inspect the marker line. When the original line has been reduced consistently, move to a finer grade and repeat; the aim is a narrow, even bevel rather than the largest amount of shiny metal.

Finishing means removing the burr, not simply making the bevel brighter. A fine diamond plate used in a light honing motion can remove or fold back a small burr, after which the edge should feel keen but not razor-sharp. Plunge bits require care because their cutters sit below the sole; follow the maker's setting so the edge can be reached without changing the bearing clearance. Test two-flute straight or hollow-ground bits at low speed on scrap timber and inspect the cut. Replace spiral or single-flute compression bits rather than reshaping their factory-formed flutes.

Build a practical maintenance routine

The best method depends on how much steel or carbide remains and whether the original geometry can be held. A slow hand-sharpening session is sensible for a lightly worn cutter, while severe damage may justify a specialist regrinding service.

Bit condition Preferred method Grit progression Practical limit
Slightly dull HSS Diamond plate or file 600–1200, then 2000+ Remove little metal and prevent rust
Lightly worn carbide Guided diamond plate 300–600, then 1000–3000 Preserve the factory bevel
Heavy rounding or a deep radius Diamond grinding wheel 80–120, then hone Heat and heavy removal can chip carbide
Chipped or missing tip Replace the cutter Not applicable Abrasive cannot restore lost carbide
Hollow-ground bit Fine guided hand passes 300–600 with care Keep its natural concavity and relief

These comparisons also show where a diamond stone is not the right tool. A coarse grinding wheel removes a deep radius faster, but it generates heat and can chip carbide or alter the bit dangerously. For a small burr, start finer than instinct suggests and preserve the factory angle. Make one correction, test on an offcut, and inspect again before removing more material. This measured approach keeps the bit useful and avoids turning a maintenance job into an expensive replacement.

A reliable workshop routine includes:

  • Degrease the cutter and inspect both flutes before choosing a grit.
  • Use approximately 300–600 grit for moderate correction and a finer grade or diamond paste for finishing.
  • Hold the factory angle with a guide, making equal, light passes across both cutting faces.
  • Remove the burr with a fine honing motion and check the edge under good light.
  • Test on scrap timber, then brush away swarf and store HSS cutters dry with a light coat of protective oil.

Home Plywood Scroll Saw Blades Band Saw Blades Drill Bits Forstner Bits Router Bits Clocks Acrylic Sheets Pattern Books Misc

Drum Sander Kit Scroll Sanders & Files Brush Sets Needle File & Riffler Sets Web Specials Scroll Saw Patterns Contact Us Ordering

Order Toll Free:  1-888-615-9663

Sloan's Woodshop - 3453 Callis Road - Lebanon, TN 37090

We Do Not Ship Outside of the US