Sloan's Woodshop - The Scroll Saw Store |
Drilling clean holes in acrylic with standard twist bitsAcrylic rewards a controlled approach because it behaves like a hard plastic rather than timber. A standard twist bit can make a clean hole, but it must cut rather than melt, and the sheet needs support so the drill does not pull it down or split the exit edge. The finished result depends on three things: a sharp bit, moderate spindle speed and a steady feed rate. These are especially important when working with polished acrylic for signs, cabinet parts, displays or templates, where a small burr or crescent-shaped break-out is immediately visible. Australian makers will usually encounter metric stock, so common 5 mm, 6 mm, 6.5 mm, 8 mm and 10 mm twist bits matter more than imperial sizes. Local hardware packs, cabinet fittings and electrical accessories should still be checked for their specified bore rather than assumed to match. Workshop equipment is normally 230 V, making an imported 120 V drill press an expensive mismatch unless it is dual-voltage. Why acrylic behaves differentlyPMMA, the plastic used in acrylic sheet, has no wood fibres to absorb heat. As a twist bit rubs, the cutting edge can melt a small channel and push a crescent of softened plastic upward. Cast acrylic is often chosen for cleaner machining, while extruded acrylic can also be drilled successfully when its different stress and finishing behaviour is understood. Drilling also creates two separate cutting conditions. The entry face can chip if the bit is dull, misaligned or travelling too slowly, while the underside can break out as the point exits. A sharp cutting edge, backing support and suitable speed prevent those failures at their source. Choosing a standard twist bitA standard general-purpose twist bit is intended to cut metal, but its flutes still remove acrylic effectively when the geometry is sharp and the machine is rigid. High-speed steel is adequate for occasional holes in thin sheet; carbide-tipped or solid-carbide tools last longer in repeated production and resist edge wear. A bit with a positive rake can grab polished stock, while a freshly ground bit usually starts more cleanly. Do not select solely by the bit’s printed diameter. A conventional twist point produces a tapered opening, so a nominal 8 mm bit may leave a cylindrical wall just under 8 mm. Check the actual bore with a rule, caliper or test piece, especially when a screw, dowel or cable gland must pass through it. The Sloan's Woodshop catalogue offers a broad reference for drill bits and accessories, although the Lebanon, Tennessee retailer takes orders by phone and states that it ships within the United States; Australian buyers should compare local suppliers before committing to international freight. The practical bit and setup checklistThe following checklist keeps the variable choices simple and makes a useful offcut test before the decorative sheet is touched. Bit and tooling choices
These choices should follow the material and required accuracy. A flexible drill can make a usable hole in a thin bracket, but it is rarely the best choice for repeated production work. Bench setup
Make every test hole in the same type or thickness of offcut. That reveals heat build-up, backing-board effects and true hole size before the component enters production. Setting up the workpiece and drillAccuracy starts before the motor is switched on. Fine pencil lines remain visible on most acrylic, while a scribed cross gives the bit a definite centre. If the hole position comes from a drawing, transfer it with a ruler and template rather than by eye; check it from both faces before clamping. The workpiece should be flat, but a heavy clamp can distort thin acrylic and leave a polished mark. Support the sheet across its wider area, place the scrap backing directly beneath the hole and tighten only enough to prevent movement. Leave clearance for the drill point and for the depth stop on a press. A drill press produces the straightest bore, while a handheld drill benefits from a guide block or a square auxiliary fence. Let the bit reach full speed before it contacts the sheet, and never force the work upward against the bit. For a related example of planning and handling decorative acrylic, a custom acrylic sign walkthrough shows the careful layout expected in a visible finished piece. Controlling heat, chips and feedUse the slowest speed that still lets the bit cut cleanly. On a drill press, a conservative starting range for a 3–12 mm general-purpose bit is roughly 1,000–2,500 rpm; larger holes need fewer revolutions and smaller ones can usually run faster. Material, bit quality and machine rigidity justify adjustment. Excessive speed generates heat, melts the edge and leaves a shiny burr, while an overly slow feed makes the bit rub. Keep a light, continuous pressure and let the flutes carry chips away. If chips pack into the flutes, withdraw the bit slightly, clear them and re-enter without shifting the centre line. Specialist water-based plastic cutting fluid, or a small amount of clean water for a thin sheet, controls heat and keeps the cut looking glassy. Avoid thinners, alcohol and oily compounds that can stress or craze the surface. A twist bit also forms an entrance chamfer, so the hole is rarely a perfect cylinder at the face. For a close tolerance, drill slightly under the required diameter with a sharp bit and open the bore gently with a hand reamer; a step drill gives even more control. Do not jump directly to a much larger bit to chase an undersized hole, because the wandering point creates an oval opening and additional heat. Fixing rough or incorrect holesA rough entry usually points to a dull bit, excessive speed or inadequate support. Reduce the speed, replace the bit and clamp the acrylic more securely before trying again. A burr around the exit often means the point has broken through without a backing board. A crescent-shaped tear calls for less feed, a sharper edge and a firm sacrificial layer beneath. If a hole is only slightly oversized, a fine file or sanding block can restore the edge. For a visibly oval or torn opening, enlarge it deliberately to the next tidy diameter and use a plug, collar or insert. A countersink may suit a screw head, but it should be cut lightly and cleared often; forcing a large countersink through acrylic often pulls a sharp lip instead. Test quality should be judged at both faces and through the full wall of the hole. Check with a pin gauge or caliper, then repeat the operation on the next piece with the same bit, speed and setup. Consistent results make the process predictable; changes in pressure or speed often create the inconsistency. Matching the method to the projectChoose the hole according to its job. A decorative sign may only need a clean fixing point, whereas a cabinet component, cable gland or load-bearing bracket has little tolerance for error. Use the manufacturer’s specified clearance and local hardware dimensions. Sydney, Melbourne and Brisbane all have sign fabricators, timber suppliers and makerspaces where offcuts, metric bits and advice can be found before buying a full sheet from overseas. Price the whole purchase, not just the sheet. Freight, insurance, minimum orders and damage in transit can outweigh a small saving on material, and a local merchant may offer the right diameter in one piece. For any direct overseas parcel, Australian Border Force generally treats consignments of A$1,000 or less as low-value goods, where 10% GST applies but customs duty is normally not collected; above that value, an import declaration and applicable tariff treatment must be checked. Large projects also benefit from a full-size layout rehearsal. Dimensions taken from a woodworking project plans collection can be transferred to an acrylic offcut to verify spacing, tool clearance and fastening points before final cutting. Sharp tools, stable support and measured feed turn an ordinary twist bit into a reliable maker of clean, repeatable holes. |
|
Home Plywood Scroll Saw Blades Band Saw Blades Drill Bits Forstner Bits Router Bits Clocks Acrylic Sheets Pattern Books Misc Drum Sander Kit Scroll Sanders & Files Brush Sets Needle File & Riffler Sets Web Specials Scroll Saw Patterns Contact Us Ordering Order Toll Free: 1-888-615-9663 Sloan's Woodshop - 3453 Callis Road - Lebanon, TN 37090 We Do Not Ship Outside of the US |