Sloan's Woodshop - The Scroll Saw Store

Home

Plywood

Scroll Saw Blades

Band Saw Blades

Clock Inserts

Acrylic Sheets

Scroll Sanders & SS Files

Drum Sander

Pattern Books

Patterns

Drill Bits

Forstner Bits

Router Bits

Brush Sets

Miscellaneous

Needle Files & Riffler Sets

Web Specials

Ordering Info

Contact Us

Drilling inside holes for piercing scroll saw blades

Scroll sawing an enclosed opening usually starts with a small drilled access hole. It gives the blade somewhere to enter and removes waste without cutting in from the edge of the workpiece. Getting that hole right matters: a tight opening can trap the blade, distort the shape or split thin plywood.

This guide explains drilling inside holes for piercing scroll saw blades in wood and similar sheet material. It covers choosing a starting hole, supporting the workpiece, using a brad-point bit and testing the fit before the saw starts. The same principles apply to clock parts, layered plywood, decorative panels and small gift boxes, whether you work at a kitchen table or in a shared workshop.

Australia adds a familiar sizing wrinkle: most local drill bits are metric while many scroll saw blades are sold in imperial widths. Think of the access hole as a working clearance rather than a decorative detail. A successful cut depends on the blade being able to enter, swivel and cut in both directions without being forced.

What the access hole must achieve

The access hole is not the finished opening. It is a starting point for the blade, usually positioned in the waste area near the outline you want to produce. The blade then reaches the perimeter and follows your drawn line. If the pilot is too large, the opening will finish loose and rounded; if it is too small, the blade may fracture when you try to turn it.

The hole must leave room for movement. A scroll saw cuts on the upstroke, so the blade needs to pivot and cut both walls of the waste. A very tight fit can leave only one side cutting and cause the workpiece to jump. Check that the teeth enter fully and that the blade can swivel before committing to the full cut.

Test in the same thickness and species as the work. A hole in thick hardwood will not predict a hole in 3 mm plywood, and an offcut with a different grain can split even when the bit is sharp. For a first attempt, use a simple circle or rounded rectangle in a stable scrap.

Matching the drill bit to the blade

Use a sharp brad-point bit for a clean starting hole. Its cutting edges begin at the tip, so it bites into the marked centre with less wander than a conventional twist bit, which often starts cutting at its outer edge. A 1.5 or 2 mm brad-point bit is a sensible starting choice for small wooden parts, but the saw and stock should decide the final size.

Use the blade’s nominal width as a reference, then verify its action in the offcut. Drill close to that width rather than making a much larger hole that gives the blade too much play. If a close fit traps the shoulders, enlarge it by a fraction. A pilot a little under the nominal width can work for a narrow blade, provided the teeth still reach and the blade can pivot.

Scroll saw specifications are often given in inches. A blade advertised at 1/32 inch is about 0.79 mm, while common blade-mounting holes of 1.07 mm and 1.35 mm describe a different measurement entirely. Check the blade width and your saw’s manual rather than converting a mounting-hole number into an access-hole size.

Supporting the work and controlling drift

Support thin material on both faces and keep the drill’s cutting direction consistent. On plywood, place the workpiece on a flat sacrificial board and use low-tack tape over the face. The backing arrests the bit as it breaks through and reduces the splintering that otherwise leaves a ragged lower edge.

Set the drill depth so the bit enters the backing only slightly. Clamp the stock without squeezing delicate panels: a wide strap clamp or a scrap caul distributes pressure across the sheet, whereas narrow pliers-style clamps can leave dents in plywood. A piece of timber with a flat working face can be more useful than a heavy bench in a small home workshop.

Mark the centre with an awl and measure from the finished edge, not a rough pencil line. Draw the final outline first, then position the pilot at a measured offset inside the waste. Keep support directly beneath the mark. Stop if the bit grabs: sharpen or change it instead of forcing a larger hole.

Threading the blade and cutting the opening

Fit the correct blade for the saw and check its tooth direction against the machine. Switch off before fitting it, then thread the blade through the access hole while the saw is stationary. The blade should sit without a sharp bend at the teeth. If it binds immediately, the hole needs more clearance or the blade needs to be aligned differently.

Start the saw at its lowest practical setting and let the blade reach full speed before feeding the work. Keep the workpiece moving steadily with light pressure. Guide the blade toward the drawn outline, then allow it to follow the curve rather than steering it sideways. Fine, even dust is a better sign than large chips or a harsh noise.

A longer, decorative practice panel inspired by surfboard project plans can reveal blade drift over a wider curve. Keep this test away from the finished component. If the blade drifts towards the waste, stop and reassess the hole; if it climbs into the finished edge, reduce pressure and check that the blade is sharp.

Comparing common drilling approaches

The best blade depends on the radius and material, not merely the access hole. Fine blades make tighter curves but twist more easily; thicker blades resist turning but need more space. A narrow, sharp blade usually negotiates a small drilled opening better than a heavy one. Plastic and acrylic require different tooth pitches and speeds from plywood, so test on scrap.

The practical differences are straightforward:

Drilling approach Best suited to Advantage Main caution
Hand drill with a brad-point bit Small wooden pieces and occasional holes Portable, inexpensive and controllable with light pressure Uneven pressure can make the bit wander
Drill press with a brad-point bit Plywood panels and repeated holes Square support and repeatable depth Clamping pressure can distort thin sheets
Hand drill with a twist bit Quick trial holes in scrap Widely available and familiar Can skid at the start and leave a burr
Step bit in a drill press Larger access holes in thin sheet Enlarges a pilot in stages, reducing grabbing Usually too large for narrow scroll saw blades

After drilling, deburr the hole’s edges with fine abrasive paper and fit the blade for a short test cut. For the surrounding surface, sanding between coats explains how to keep sealed plywood smooth without rounding its edges. Keep adhesive and finish off the teeth, and do not use a kinked blade to compensate for a poor access hole.

A reliable selection and ordering checklist

Sloan's Woodshop lists plywood, scroll saw and band saw blades, drill and router bits, sanding tools, files, clock inserts, acrylic sheets, patterns and books. Ordering is by toll-free telephone rather than online checkout, and the stated delivery area is within the United States. An Australian buyer should establish the shipping route, freight-forwarding arrangements and total landed cost before committing to a parcel.

Customs is part of the purchase, not an afterthought. If a freight forwarder is used, check that it can receive the retailer’s parcels and declare the contents correctly. Australian GST, duty, postal charges and handling fees may apply, depending on the shipment’s value and transport method. Plywood and wooden packaging can also attract biosecurity questions, so check current import requirements before the goods leave the United States.

Local sourcing is often simpler for consumables. Hardware stores in Sydney, Melbourne and Brisbane commonly stock metric drill bits and plywood, while a local timber supplier can often cut a small offcut without international postage. Australian workshops also use 240 V power, so check voltage and plug standards for any separate powered machine. Radiata pine, plywood and MDF are common project materials, but their density and veneer structure still affect how a hole behaves.

  • Measure the blade width and keep a sample of your preferred blade before choosing an access-hole size.
  • Test a brad-point bit on an offcut of the same thickness, supporting both faces.
  • Drill at a marked centre with light pressure, and stop if the bit grabs or wanders.
  • Confirm that the blade can enter and pivot in the hole before switching the scroll saw on.
  • Ask Sloan's Woodshop to confirm the blade specification, shipping route and customs treatment before ordering.

Home Plywood Scroll Saw Blades Band Saw Blades Drill Bits Forstner Bits Router Bits Clocks Acrylic Sheets Pattern Books Misc

Drum Sander Kit Scroll Sanders & Files Brush Sets Needle File & Riffler Sets Web Specials Scroll Saw Patterns Contact Us Ordering

Order Toll Free:  1-888-615-9663

Sloan's Woodshop - 3453 Callis Road - Lebanon, TN 37090

We Do Not Ship Outside of the US