Sloan's Woodshop - The Scroll Saw Store

Home

Plywood

Scroll Saw Blades

Band Saw Blades

Clock Inserts

Acrylic Sheets

Scroll Sanders & SS Files

Drum Sander

Pattern Books

Patterns

Drill Bits

Forstner Bits

Router Bits

Brush Sets

Miscellaneous

Needle Files & Riffler Sets

Web Specials

Ordering Info

Contact Us

Installing a band saw blade for reliable tracking

A band saw that cuts straight on one board and wanders on the next usually has a blade that is not sitting or moving correctly. Lateral drift can produce tapered cuts, uneven edges and burnished timber. Installing a band saw blade correctly for proper tracking means correcting tension, guide clearance and wheel alignment before making fine tracking adjustments.

Tracking is the blade’s side-to-side position as it travels around the wheels. The cutting edge should hold a steady line instead of drifting towards one side of the wheel tread. Tension stabilises the band, guide blocks limit flexing, and wheel alignment establishes its path. These adjustments interact, but none should be used as a substitute for another.

Unplug the saw, let a hot blade cool and identify its wheel layout, guide type and adjustment controls from the maker’s manual. Wear eye protection when the saw runs and keep hands away from the moving band. In Australia, check the nameplate: a US 120 V saw cannot simply be connected to a 240 V supply, and any conversion needs assessment by a qualified electrician.

Why a band saw blade wanders

A wandering blade usually shows itself as a cut that becomes wider, narrower or visibly curved. Look at the finished edge rather than judging only the shape of the workpiece. Blade wander can also make the band rub against a guide, producing polished marks and heat that dulls the cutting edge, especially on hardwood.

Common causes include inadequate tension, a dull or resin-coated blade, guides set too tightly, and wheels that are out of alignment. A dull blade can wander backwards under load and make tracking adjustments seem ineffective. Tightening the wheel-tracking control cannot repair a damaged cutting edge or compensate for a guide dragging on the band.

Start with the simplest faults: blade damage, tension and guide contact. If a new blade still wanders after those checks, investigate wheel alignment rather than repeatedly turning the tracking knob. This order saves time and prevents an overcorrected setup that becomes difficult to diagnose.

Choosing a blade for the saw and timber

Use a blade whose width matches the saw’s capacity and the material being cut. The listed width must also suit the wheel and guide system; a blade that is too wide cannot run correctly even if it fits between the wheels. For general hardwood work, medium teeth are often more serviceable than very fine teeth, which suit clean curves in thinner material better.

The band saw blade range covers several tooth patterns and widths, so compare the blade width, tooth pitch and intended application before ordering. Fine-toothed blades suit plywood and gentle curves; heavier patterns suit thicker stock. Teeth should point towards the cutting edge and into the workpiece as the band travels downward.

Australian timber adds another consideration. Jarrah, spotted gum and many imported hardwoods can be hard on the cutting edge, while humid conditions around Sydney and Brisbane can make resin stick to the band. Choose a durable tooth pattern for repeated hardwood work rather than relying on aggressive tracking to solve poor cutting.

Purchasing from the United States needs a logistics check. Sloan’s Woodshop is based in Lebanon, Tennessee, takes catalogue orders by telephone and publishes shipping within the United States. Compare prices in Australian dollars, allowing for international freight, forwarding and possible blade damage. Australian GST can apply to a low-value overseas parcel once its value, including freight and insurance, exceeds A$1,000. The Australian Consumer Law and ACCC guidance mainly concern purchases in Australia, so a direct overseas purchase may not carry the same guarantees.

Setting blade tension correctly

Release the blade tension before removing the old band. Support it as you remove it so it cannot twist, and inspect the teeth, back and weld. Check the replacement as well, and reject any blade with missing teeth, cracks, significant set damage or an edge that cannot be restored.

Fit the replacement in the direction shown by the manual and set the initial tension on the manufacturer’s scale rather than tightening the tension screw by feel. Many saws have a marked range for common blade widths, and staying within it helps the blade track predictably.

Allow the new blade to settle for the time recommended by the manual, then recheck and adjust the tension. It should feel taut and straight without being stretched aggressively. A straightedge across the free span can reveal obvious slack, but should not replace the saw’s tension scale. Overtension increases vibration, while insufficient tension lets the band wander.

Fitting the blade and adjusting the guides

Release the tension again before adjusting the guide assemblies, and support the blade rather than forcing it against a guide. Wear cut-resistant gloves when handling the sharp band, but keep hands away from a running saw; a blade can cut through a glove.

Guide blocks and roller guides should support the blade close to its back without pinching it. Set them to touch lightly, using a feeler gauge and the manual’s clearance; many ball-bearing guides run only a fraction of a millimetre from the blade. Position the guides slightly behind the teeth, rather than pushing against the sharp edge.

Pay attention to the lower guide and any thrust bearing, which should spin freely with tiny clearance. The upper guide may need a small rearward tilt to support the blade, but excessive tilt twists the band. If the saw uses a chip brush, refit it so it cleans the wheel without touching the blade. Restore the specified tension after moving the guides, then check their contact again.

Aligning the wheels and setting the tracking path

Both wheels should be square to the blade path and free of flat spots, grooves or built-up resin. The band should ride roughly in the centre of the wheel tread. Check that the saw stands stably and that the wheel assemblies have not shifted. A wheel leaning inwards can make tracking erratic even when the blade and guides are correctly adjusted.

Use the wheel-tracking adjustment only after tension and guide clearance are right. If the manual calls for a running adjustment, fit the guards or use the maker’s guard-safe procedure before powering up. Turn the control in small increments, following its direction, and allow the blade to settle after each change. Align the lower wheel where the model permits adjustment.

Make a trial cut on scrap timber and compare the finished edge with a pencil mark. Repeat after the blade has run for several minutes. The tracking knob should correct consistent sideways drift, not rescue a blade that wanders in both directions. If the adjustment continually reverses, stop and inspect the guides, tension and wheels again.

Testing the cut and diagnosing remaining faults

Make a slow test cut on scrap and inspect the edge, then repeat once the blade has warmed. The cut should stay the same width around the wheel. Listen for changes in bearing noise and watch for smoke or polish on the band. These signals can reveal a rubbing guide or resin build-up before the blade is ruined.

If the same wander occurs with a new blade, concentrate on wheel alignment and guide setup. If a known-good blade produces a straight cut, check tension and the direction of the replacement. Blades with cracked welds, missing teeth or bent backs should be replaced. A dull but sound blade may be sharpened if its teeth remain intact.

Fine-tooth blades need clearance and suitable speed for tight curves; excessive pressure can make the band wander even when tracking is good. This small-curves guide looks at keeping the blade supported during delicate work. A steady cut depends on blade condition, feed pressure and guide spacing.

Reliable band saw setup recommendations

A repeatable setup routine prevents most tracking problems:

  • Fit the correct blade width, tooth pattern and direction for the saw and material.
  • Set tension to the manufacturer’s scale before touching the tracking control.
  • Check wheel alignment, then set guide blocks and roller guides to light contact.
  • Make small tracking corrections and verify them with a cut on scrap timber.
  • Replace damaged blades and remove resin from the wheels, guides and blade.
  • Fit the guards, wear eye and hearing protection, and keep hands away from the moving blade.

Australian workshops should use an RCD-protected outlet and follow the work health and safety rules for their state or territory. Safe Work Australia publishes model codes that support those rules, while local legislation determines what applies in each workplace.

Record the blade type and tension setting, then recheck the setup after the first few cuts. New blades may need a brief running-in period, and temperature or humidity changes can affect tension. A correctly installed band saw blade should hold one clean line under steady pressure. Work through tension, guides and wheel alignment in that order, reserving fine adjustments for the final stage.

Home Plywood Scroll Saw Blades Band Saw Blades Drill Bits Forstner Bits Router Bits Clocks Acrylic Sheets Pattern Books Misc

Drum Sander Kit Scroll Sanders & Files Brush Sets Needle File & Riffler Sets Web Specials Scroll Saw Patterns Contact Us Ordering

Order Toll Free:  1-888-615-9663

Sloan's Woodshop - 3453 Callis Road - Lebanon, TN 37090

We Do Not Ship Outside of the US