Sloan's Woodshop - The Scroll Saw Store

Home

Plywood

Scroll Saw Blades

Band Saw Blades

Clock Inserts

Acrylic Sheets

Scroll Sanders & SS Files

Drum Sander

Pattern Books

Patterns

Drill Bits

Forstner Bits

Router Bits

Brush Sets

Miscellaneous

Needle Files & Riffler Sets

Web Specials

Ordering Info

Contact Us

Matching Band Saw Blade Width to Curve Radius

The relationship between band saw blade width and the radius of a curved cut is a compromise. A wide blade is laterally stiff, so it resists wandering and tends to follow a straight line cleanly. A narrow blade can wrap around a tighter curve, but it deflects more readily and needs careful tension, guide adjustment and feeding. Using the wrong width can produce wavy edges, burned marks, blade twist, scored workpiece faces or a snapped blade.

Before choosing a blade, find the smallest radius on the drawing and measure the path the blade teeth will follow rather than the outside edge of the finished workpiece. A blade selection chart, the saw maker’s recommended range and the material being cut should agree. If a chart is unavailable, begin with the manufacturer’s general band saw range and test a narrower blade on an offcut rather than forcing a wider one around the curve. A blade labelled for scroll saws should not be assumed to have the same minimum radius on a band saw.

How width changes the way a blade turns

Blade width controls how well the strip resists sideways bending. A broader band saw blade has more mass and stiffness, which helps it remain supported between the wheel and the workpiece. That support is valuable on straight cuts and long passes through thick timber. On a curved cut, however, the blade must change direction continuously, and those same qualities can make it buckle or run away from the intended path.

The curve radius is the radius of the arc traced by the blade teeth. Small inside radii demand frequent, abrupt changes in direction, while large sweeping radii allow the blade to settle into a smoother arc. The same blade may negotiate a tight curve in thin plywood but struggle with the same radius in thick hardwood because greater cutting force increases sideways loading.

A blade that is too wide often reveals the problem through heat and scoring on the exit face. A blade that is too narrow may wander, leave an uneven kerf or allow the guide blocks to crowd the cut. The correct pairing is therefore not the widest blade that fits the saw. It is the narrowest blade that can hold the required curve while remaining stable in the cut.

Matching tooth and material choices to the cut

Width is only one part of a band saw blade specification. Blade thickness affects flexibility and kerf; tooth pitch sets how aggressively the teeth enter the material; and tooth set determines how much sideways clearance each tooth has. Fine teeth and thin, low-set blades suit delicate curves and thin stock, while fewer, larger teeth provide more room for chips to escape from thicker sections. Heavy set helps the teeth clear the wood but can impair tracking in a tight curve, whereas a low set gives a cleaner cut and demands sharp teeth.

These starting points relate blade width to the curve and material:

  • For small scrolls in 3–6 mm plywood, compare narrow 3.2 mm and 4.8 mm blades with a fine-tooth, low-set profile, provided the saw accepts that width.
  • For cabinet cut-outs and templates with medium radii, 4.8–6.4 mm widths often balance curve access with useful stiffness; verify the saw’s compatible blade range.
  • For broad curves in thick hardwood, 9.5–12.7 mm blades can be appropriate when the radius is generous and the tooth pitch can carry the load.
  • For acrylic sheet, select a blade intended for plastic rather than relying on kerf width alone; an unsuitable woodworking tooth can melt, chip or leave a ragged edge.

Use the blade maker’s curve-rating chart together with the saw manual because guide geometry and wheel diameter affect the usable minimum radius. A useful reference for United States blade descriptions is Sloan's Woodshop range, a catalogue based in Lebanon, Tennessee that includes scroll saw and band saw blades alongside woodworking supplies. It uses toll-free telephone ordering and states that it ships within the United States, so Australian shoppers should treat it as a product reference and confirm that a local supplier carries an equivalent blade.

Checks that protect the blade and the cut

A blade with the correct dimensions can still cut badly if the saw is not ready. Wheel condition, blade tracking, guide position and tension all affect the minimum radius a band can hold. A tired wheel, packed debris or a blade running against a guide can impair tracking and increase heat, while incorrect tension makes an otherwise suitable blade wander or buckle.

Complete these checks before making the full-size cut:

  • Confirm compatibility: Measure the blade width, check the wheel and guide clearance, and verify the manufacturer’s approved width range before fitting it.
  • Set tracking and tension: Let the band run at operating speed, confirm it sits centred, then tension it to the saw’s specified range rather than using extra force.
  • Adjust the guides: Bring them close enough to support the blade without pinching it, and set the upper guide at the saw maker’s recommended distance behind the tooth line.
  • Run a test cut: Use an offcut with the same thickness and a radius close to the tightest one; inspect for drift, heat and a consistent kerf.

During the cut, feed the work into the teeth rather than steering it around the curve. Keep the workpiece supported, maintain a steady rate and let the blade do the turning. On a tight radius, reduce pressure and take short passes if needed; forcing a blade sideways converts a curve into a twisting force. Release the blade tension before changing blades, and allow a hot blade to cool before handling it.

Australian workshop considerations

Australian tool shops and timber merchants usually specify dimensions in millimetres, while many imported blades from the United States are marked in inches. Common band saw widths correspond to 1/8 inch (3.2 mm), 3/16 inch (4.8 mm), 1/4 inch (6.4 mm), 3/8 inch (9.5 mm) and 1/2 inch (12.7 mm). Measure the actual blade or check the saw manual rather than relying on a rounded conversion, as similarly named widths from different manufacturers are not always interchangeable.

The buying pattern in Australian hobby shops is often compact: one 2400 × 1200 mm sheet of plywood or MDF is shared among several weekend projects, with offcuts reserved for jigs and small parts. Independent timber yards and larger home-improvement stores in Melbourne, Sydney, Brisbane and Adelaide stock suitable sheet goods, hardwood lengths and accessories, although local hardwood thickness and availability vary. Pieces made from jarrah, spotted gum or imported hardwood should be matched to the blade’s material rating because harder timber generates more heat.

For a paid workshop, Safe Work Australia’s model work health and safety legislation provides the national framework, with state and territory rules adding specific obligations around guarding, training and risk management. A blade must still be suitable for the machine and task. Australian Consumer Law requires goods to match their description and be of acceptable quality, making the specification, invoice and seller’s advice useful records when assessing a blade that performs poorly.

A repeatable blade selection process

Begin with the geometry: mark the tightest inside radius on the drawing, identify any compound curve and note whether the saw will be used for push-cutting or resawing. The blade must be compatible with the saw’s wheel width, guide clearance and permitted tension range. Next, choose the tooth material and profile for the workpiece. General carbon-steel blades work well in ordinary wood, bi-metal options are useful in abrasive hardwood or when heat is a concern, and plastic-cutting teeth are essential for acrylic.

Test rather than relying on a single number. A curved offcut exposes poor tracking more clearly than a straight test, while close inspection of the kerf shows whether the teeth are cutting, rubbing or wandering. Record the blade width, tooth count, set, material, feed rate and saw speed once the right combination is found. That record is more valuable than a universal curve chart because the same blade behaves differently on different saws and in different timber.

Correct blade width and curve radius work together with tension, guides and handling. The blade can then follow the drawn arc without lateral stress, the cut remains suitable for the intended joinery, and the teeth preserve the surface of the workpiece. For a small Australian workshop, this measured approach avoids buying by habit and makes each replacement blade an informed choice rather than a guess.

Home Plywood Scroll Saw Blades Band Saw Blades Drill Bits Forstner Bits Router Bits Clocks Acrylic Sheets Pattern Books Misc

Drum Sander Kit Scroll Sanders & Files Brush Sets Needle File & Riffler Sets Web Specials Scroll Saw Patterns Contact Us Ordering

Order Toll Free:  1-888-615-9663

Sloan's Woodshop - 3453 Callis Road - Lebanon, TN 37090

We Do Not Ship Outside of the US