Sloan's Woodshop - The Scroll Saw Store |
A Reliable Band Saw Setup for Thin ResawsSetting up a band saw for resawing thin stock from boards can turn a broad slab into consistent panels, laths or decorative strips while preserving the timber’s face grain. The cut is wonderfully productive, yet the quality depends on blade choice, guide alignment and support long before the motor starts. With a narrow blade and a stable table, even stock only a few millimetres thick can be sliced accurately. This guide covers the practical setup, from choosing a suitable resaw blade to judging a test cut and feeding the work safely in an Australian workshop. Set the target dimensions firstBegin with the finished thickness, number of slices and acceptable kerf. Remember that a 3 mm blade consumes part of the wood, so the blade choice and final measurement must agree. For a one-off drawer divider, mark the spacing on the board; for repeated box panels, calculate total stock loss before cutting. Australian timber yards in Brisbane, Melbourne, Sydney and Adelaide offer rough-sawn and dimensional hardwood, though species vary by region. Spotted gum and blackbutt are familiar eastern timbers, while jarrah is strongly associated with Western Australia. Inspect each board rather than assuming one species responds to resawing in the same way as another. Sloan’s woodworking supply catalogue is a useful reference for blade widths, files and workshop accessories. It is a telephone-order store based in Lebanon, Tennessee, with delivery within the United States, so Australian buyers should not assume local checkout or freight. Compare specifications with your own machine and follow its manual for blade width, tension and guide setup. Match the blade to the cutResawing hardwood usually calls for a narrow blade in the 1/8 to 1/4 inch range, equivalent to roughly 3.18–6.35 mm. Fine woodworking saws may also offer 1/16-inch or 3/16-inch blades. A three-tooth pattern is common for hardwood, while a somewhat finer pattern can give a cleaner cut in very thin stock. Blade width, tooth pitch and tooth set must all suit the machine and workpiece. A narrow blade is flexible and can wander if blunt, badly set or under-tensioned. A fresh, sharp blade with modest set usually gives the cleanest kerf. Install it according to the saw manual, position the guide blocks close enough to support the blade without rubbing, and use the thrust bearing where fitted. Excessive set invites drift and snipe; insufficient set can make the blade rub. Australian benches commonly run on 230–240 V with Type I plugs, while many machines sold in United States catalogues use 120 V. Do not connect an imported saw to local power unless its rating and certification have been checked. Commercial buyers should also allow for GST, applicable duty, brokerage and freight, using an Australian customs broker for commercial imports and having an electrician assess RCD protection. Prepare the machine and support systemSupport the timber on both sides of the blade. A wide flat board can bridge the table, but a long workpiece needs a roller stand or stable outfeed table; unsupported ends twist downward, pull the blade sideways and produce a wedge-shaped slice. Fit the outfeed rollers slightly below table height and keep the fence clear of the blade path. A square fence helps hold the rear edge of the stock, but it should guide rather than clamp the board. A tall fence may obstruct a narrow blade, so check the machine’s recommended fence position. Before each pass, clear chips from the table and throat so the timber remains in full contact with the metal surface. Dust extraction should be connected before cutting, particularly in small urban sheds where airborne dust settles on tools and finished timber. Position the collection hood or nozzle close to the blade without touching moving parts. Match the extractor to the volume of fine sawdust produced and avoid recirculating particles into the breathing zone. Pre-cut safety and setup checksDisconnect the power before fitting a blade, adjusting guides or clearing a jam. Confirm the blade is correctly installed, tensioned and free of resin. Set the table, fence and outfeed rollers square to the cutting path. Keep hands outside the blade path and use a suitable push device. Check guards, dust extraction and emergency stopping arrangements. Prove tracking with a test cutTrack the blade with the machine stopped and disconnected. Follow the manual for loosening the guide blocks and adjusting the rear thrust bearing; some saws specify a slight angle rather than a parallel setting. A tracking indicator or a light mark on the bearing housing helps show movement. Never use the blade itself as the adjustment reference. Make the first test cut on scrap with similar grain. A pencil line on the top should travel through the slice rather than wander toward one side. Look for a straight kerf, a smooth face and even thickness. A fuzzy surface suggests a dull blade, while a wandering line may point to tension, guide alignment, uneven stock or feed pressure. Fine saw marks are normal, but they should be consistent. Measure across several slices instead of judging from the edge alone. If the kerf varies in width, stop and correct the setup; a wandering blade makes consistent spacing impossible. When resawn strips will later be joined to acrylic, the wood and acrylic glue choices should be compared before assembly, since adhesive compatibility and accurate joints are separate requirements. Control the feed and keep the operator safeFeed at a steady, modest pace and let the teeth remove material. Do not force the board or push sideways to correct drift. Keep the workpiece flat against the table and use the fence only as rear support. For narrow strips, a purpose-made bandsaw push device keeps fingers farther from the teeth while preserving control. Stand to the side of the blade path, not in line with it. Keep hands on the incoming stock well away from the teeth, and never reach around the blade to retrieve a cutoff. Stop the saw before removing loose offcuts, adjusting the fence or checking a cut. A dull blade can create enough friction and heat to stall, burn the wood or cause kickback. For repeatable results, mark the feed direction and begin each pass at the same end. Brush chips toward the rear, support the piece as it approaches the blade and let the outfeed table carry its weight after the cut. Work slowly enough that the motor sound remains even and the board does not wander. A dependable cutting sequenceSquare and mark the board, then calculate finish thickness from the actual kerf. Set the fence and support rollers before starting the motor. Guide the first few centimetres gently, then maintain an even feed. Watch the pencil line to detect early blade drift. Support the separated slice and clear waste only after the blade stops. Maintain the setup for local conditionsClean resin and dust from the blade, guides and wheel hubs after use. Store spare blades flat or on a suitable holder so they do not develop set, and sharpen or replace a blade as soon as it stops slicing cleanly. Check guide spacing, belt condition and table alignment periodically, since small changes can accumulate into uneven stock. Seasonal conditions matter in Australia. Humid summers in Brisbane and coastal Sydney can increase moisture movement, while Melbourne and Adelaide often experience sharp changes between dry summers and damp winters. Acclimatise boards in the room where they will be machined, measure moisture when precision matters, and allow finished pieces to settle before final assembly. Small Australian workshops can turn clean thin stock into batch-made boxes, plaques or nursery accessories. The coordinated presentation of a gift retailer such as Belly Baby Wear illustrates how a narrow product range can appear coherent to buyers. Consistent labelling, accurate descriptions and tidy packaging can support sales in the local market, provided every slice starts with square, stable and accurately guided cutting. |
|
Home Plywood Scroll Saw Blades Band Saw Blades Drill Bits Forstner Bits Router Bits Clocks Acrylic Sheets Pattern Books Misc Drum Sander Kit Scroll Sanders & Files Brush Sets Needle File & Riffler Sets Web Specials Scroll Saw Patterns Contact Us Ordering Order Toll Free: 1-888-615-9663 Sloan's Woodshop - 3453 Callis Road - Lebanon, TN 37090 We Do Not Ship Outside of the US |