Sloan's Woodshop - The Scroll Saw Store

Home

Plywood

Scroll Saw Blades

Band Saw Blades

Clock Inserts

Acrylic Sheets

Scroll Sanders & SS Files

Drum Sander

Pattern Books

Patterns

Drill Bits

Forstner Bits

Router Bits

Brush Sets

Miscellaneous

Needle Files & Riffler Sets

Web Specials

Ordering Info

Contact Us

Using a band saw to pre-cut scroll saw pattern profiles

Scroll sawing becomes faster and more predictable when a band saw removes the bulk of the waste first. Instead of forcing a scroll saw through a wide strip of plywood, the band saw follows the outer shape of the pattern and leaves a smaller blank for the finer machine. This approach suits decorative cutouts, silhouettes, scroll work, layered plywood projects, and shapes with long sweeping curves.

The key is to distinguish between rough cutting and final cutting. A band saw establishes the basic contour with a little extra material still attached, while the scroll saw defines the finished profile. This division of work reduces blade stress, limits wandering through thick stock, and gives the finer saw a stable platform. It also makes replacement patterns more consistent because each stage has a clear purpose.

Australian makers often work in small home workshops, apartment hobby rooms, shared sheds, or community craft spaces, so reducing material handling is valuable. Measurements in these workshops are usually metric, while inherited American machines and plans may still use inches. The same practical care applies to material selection, machine setup, and workshop workflow regardless of where the project is made.

Why band saw rough-cutting improves scroll work

A scroll saw blade is narrow, but it still needs a clear path through the material. If it must remove a large area outside the pattern, the blade can pull sideways, snag, or twist around a curve. Pre-cutting with a band saw removes that burden. The first machine follows the rough outline, while the scroll saw only removes the narrow allowance between the rough edge and the drawn profile.

This is especially helpful in plywood, MDF, acrylic, and thicker craft timbers. A broad offcut is heavy and awkward for a scroll saw table, and excess material increases the chance of vibration. A smaller blank is easier to clamp, supports itself better, and allows the operator to turn it naturally as the outline changes. The scroll saw then performs the task for which its fine, controllable blade is best suited.

The scroll saw catalogue from Sloan’s Woodshop can help with blade selection and accessory ideas, although the store is arranged around United States shipping and toll-free phone ordering. Australian buyers should confirm freight arrangements and current stock rather than assuming international fulfilment, or compare specifications with a local supplier before purchasing.

Set up the band saw for accurate rough cuts

Begin with a clean table, correctly aligned blade guides, and a blade suited to the material. The blade should be sharp and tensioned according to the machine manufacturer’s instructions. Dull teeth create a wider, wandering kerf and can leave a rough surface that is difficult to follow with a scroll saw. On thin plywood, the blade should run steadily without deflecting as the stock is guided into the cut.

Secure the workpiece and keep both hands clear of the blade path. Large sheets need support on both sides of the table so their weight does not pull the cut off line. Small pieces should be clamped rather than held by hand. A push stick or other approved guide can help when the pattern allows a straight approach, but it should never replace proper clamping or create a dangerous reach toward the blade.

Power supply is an important consideration for Australian workshops. Most local outlets provide 240 volts, while machines imported from the United States may expect 110–120 volts. An imported band saw should be checked by a qualified electrician before use. Measure existing patterns in millimetres and convert imperial plans carefully; a two-millimetre allowance that seems insignificant on paper can represent a substantial error on a large decorative panel.

Transfer the profile and choose suitable stock

The full-size master pattern should be fixed cleanly to the material before cutting. Masking tape works well on many plywood faces, but low-tack tape or a suitable paper template is preferable where the surface must remain unmarked. For acrylic, use a product designed for that plastic and avoid applying adhesive that could soften or cloud it. Trace the complete outline, including internal openings, and mark the direction of the grain if the design has one.

Material choice affects how closely the band saw can follow the line. Standard plywood is stable and easy to work, while MDF offers smooth edges but can dull blades quickly and is sensitive to moisture. Australian hardwood offcuts, including spotted gum, blackbutt, or huon pine, can produce attractive results but may be harder, more brittle, or more abrasive than softwood. Radiata pine is easier to cut, yet its knots and resin can still change blade performance.

Local sheet dimensions also need consideration. Australian plywood is commonly available in metric sizes such as 2400 by 1200 millimetres, while imported sheets may use North American dimensions. If two sheets must be joined, check their actual thickness as well as their nominal size. For a fabric or quilting mock-up, a thin layer of batting from quilting supplies can test the contour without risking the finished panel, although the final cut should still be made in the real material.

Handle tight corners and sweeping curves

Long curves are usually the easiest part of a band-saw rough cut because the blade can travel through the waste area without obstruction. Sharp inside corners are different. A continuous curve cannot remove every piece of waste because the blade cannot turn tightly enough within the corner. Plan short relief cuts that meet near the inside point, then shape the remaining waste with the scroll saw.

Leave enough material for the scroll saw to correct the band-saw path. An allowance of roughly one or two millimetres is a useful starting point, but the exact amount depends on blade type, material thickness, and how steadily the rough cut was made. Attempting to meet the finished line entirely on the band saw saves little time if it causes a corner to break out or the scroll-saw blank to lose its support.

Circular features need particular care. A clock face introduces a hole that must fit the insert as well as the surrounding decorative profile. This guide to Forstner bit hole sizing explains the fitting issue in useful detail. Measure the actual insert available in Australia, since hardware dimensions may differ between brands, and test the bore before committing to the full sheet.

Move cleanly from rough cut to final profile

Once the band saw has produced the rough blank, mark the scroll-saw allowance around the complete pattern. If the outline was transferred to the face, transfer it again to any backing material that will be attached afterward. Use a sacrificial backing to reduce the risk of breakout on thin plywood. Position the backing so its edge follows the finished profile rather than the rough outline, which would leave too much material to remove accurately.

The scroll saw should then follow the final line in a controlled sequence. Outside curves can be taken continuously, while inside corners may require a series of short turns or relief cuts. Keep the blade moving at a steady rate and guide the work rather than twisting it. If the blade begins to scrub or the cut drifts, stop and correct the cause instead of forcing the blank around the blade.

Acrylic requires a different approach from wood. It heats quickly, can gum a blade, and may crack if the cut is interrupted. Use a blade recommended for acrylic, reduce heat with appropriate cooling, and support the sheet so it cannot close around the blade. Test on an offcut first. For very small or highly detailed parts, a purpose-built laser cutter may be more predictable than either saw, although the same full-size pattern and allowance principles can still guide preparation.

Build a reliable workshop workflow

A consistent process is more valuable than a complicated one. Preparation, rough cutting, and final scroll sawing should each have a separate stage, with the material checked before the next machine begins. Australian workshops need to account for local conditions as well, especially humidity and temperature changes that can affect MDF, plywood faces, and paper templates.

  • Draw the complete pattern at full size, including grain, holes, and waste areas.
  • Choose a band-saw blade and cutting speed appropriate to the material thickness.
  • Clamp the sheet securely and support any portion extending beyond the table.
  • Leave a small, even allowance outside the finished scroll-saw profile.
  • Make relief cuts for tight corners before switching to the finer saw.
  • Compare test pieces before cutting the final panel, especially in acrylic or dense timber.

Allow new sheet material to acclimatise to the workshop before final cutting, particularly in humid coastal areas or rooms with wide temperature swings. A pattern transferred immediately after unpacking can shift as the sheet adjusts, leaving an inaccurate edge. Likewise, store reference templates flat and keep them away from damp floors in a suburban shed or regional workshop.

For Australian makers, local hardwood and plywood suppliers can provide samples for testing, while existing sheet goods and inherited scroll saws can still support the method. The essential advantage remains the same: the band saw performs controlled rough cutting, and the scroll saw creates the precise, decorative profile with less stress on the blade and less waste on the bench.

Home Plywood Scroll Saw Blades Band Saw Blades Drill Bits Forstner Bits Router Bits Clocks Acrylic Sheets Pattern Books Misc

Drum Sander Kit Scroll Sanders & Files Brush Sets Needle File & Riffler Sets Web Specials Scroll Saw Patterns Contact Us Ordering

Order Toll Free:  1-888-615-9663

Sloan's Woodshop - 3453 Callis Road - Lebanon, TN 37090

We Do Not Ship Outside of the US