Sloan's Woodshop - The Scroll Saw Store |
Using a brad point drill bit for clean angled holes in plywoodAn angled hole in plywood looks simple until the bit skids across the face veneer, catches a hidden glue line or bursts through the lower sheet. A brad point drill bit is especially useful here because its pointed tip begins the hole in one spot, helping the cutting lips enter cleanly before the full diameter is established. The best result still depends on a sharp edge, a rigid angle and controlled feed. A drill press or purpose-built jig keeps the hole aligned with the timber, while a sacrificial backing piece protects the exit face. This guide explains the setup, Australian buying considerations and the habits that keep repeated holes consistent. Why the point matters in plywoodBrad point bits differ from ordinary twist drills because their flutes end in a sharp, narrow point rather than cutting immediately at the full body diameter. The point penetrates the face veneer and gives the bit a defined starting place. That feature is valuable in plywood because thin decorative veneers can shift, lift or split when a broad cutting lip lands off-centre. The point does not create a polished hole. The flutes still remove the circle of wood, and plywood’s alternating veneers and adhesive lines can produce a ragged wall or an exit blow-out. For small and medium locating holes, however, a sharp brad point starts more predictably than a blunt twist drill and is easier to control at an angle. Large clean recesses remain the stronger territory of a Forstner bit or hole saw. For pilot holes, angled dowel holes and fixings through stacked panels, the brad point’s positive start usually makes it the more practical tool. Larger laminated work also benefits from controlled drilling; plywood surfboard plans provide a useful example of the scale on which small alignment errors become visible. Choosing the right bit for the jobChoose diameter from the finished hole, not from the width of the project. A 3 mm bit may suit a small dowel or pilot, while 6–10 mm bits are common for larger pegs and bolts. Check shank and chuck compatibility too, especially when the drill press and handheld drill use different chucks. Several useful selection criteria can guide the buying process. For small locating holes, choose a 2–4 mm bit for a pilot or slender dowel, taking care not to split the face veneer. Dowel and peg holes require matching the drilled diameter to the dowel, leaving only the fit allowance recommended for the joint. Bolt clearance involves measuring the fastener and adding the specified clearance; an oversized hole hides alignment and weakens the connection. Large recesses necessitate selecting a Forstner bit or hole saw when the goal is a broad, flat-bottomed opening rather than a locating hole. Finally, keeping a fresh matched spare on hand ensures a damaged point cannot ruin an otherwise sound setup. Most brad points use a 118° or 135° included point, with precision versions offering a finer tip for delicate layouts. The angle is less important than sharpness and size. A standard point from a reputable toolmaker is usually more dependable than a worn or poorly finished cheap bit. Test the chosen bit in an offcut from the same sheet. If it catches or burns, change the setup before drilling visible panels. Replace a brad point once its tip becomes rounded or its cutting lips lose their clean edge. Setting up a repeatable angled holeFor production work, use a drill press whenever possible. Its table can be tilted to the required angle, and the quill then approaches the panel on one fixed axis. Check the table setting against an engineer’s square and make a test hole in scrap before touching the project panel. Protect the workpiece with an angled cradle or purpose-built jig. The supporting surfaces must match the drill angle, while a stop or fence holds the panel against sideways movement. Clamp close to the cutting area, but tighten only enough to prevent vibration; crushing plywood can mark the face and spoil a decorative edge. Layered work offers a useful scale model: the layered fretwork clock project shows how many small angled starts can accumulate in a decorative plywood assembly. Make one practice panel with the same layers, clamps and bit angle as the final work. If the hole wanders in practice, alter the jig rather than trying to steer the drill by hand. Drilling without chips or wanderingSet speed before feed. Common 3–6 mm brad points in plywood often work around 1,500–2,500 rpm on a drill press, although manufacturer guidance and bit condition take priority. Excessive speed heats glue and burns the exit; too little speed can make the point rub rather than cut. Place a thin sacrificial waste board under the plywood, or recess the workpiece over a scrap opening so the bit enters air at breakthrough. This supports the lower veneer and gives torn fibres somewhere to go. A strip of low-tack tape over the entry area can also reduce edge lifting, but it must not wrinkle under the clamp. A precise drilling sequence ensures accuracy and safety. Mark the axis with a fine square or protractor, then make a shallow centre dimple so the point has a definite target. Align the point with the dimple before the bit rotates at full working speed, keeping the tool’s axis on the marked line. Start the spindle, bring the point into the dimple and increase feed gradually until the full cutting diameter enters the wood. Keep steady pressure and listen for a steady cutting note; stop if the bit heats, snags or changes pitch. Withdraw the bit completely before clearing chips, then restart to prevent a spiral of shaved plywood from wrapping around the flutes. On a handheld drill, keep the body square to the jig, brace the tool with both hands and use the jig’s pilot to prevent rolling. Changes in resistance often signal a dull edge, glue line or excessive feed pressure. Buying and shipping for Australian workshopsAustralian buyers will usually choose plywood by metric thickness: 3, 4, 6, 9, 12 and 18 mm are common, whereas US listings often use fractions of an inch. Bunnings and Mitre 10 carry general stock, while Hobbyco and independent timber merchants around Melbourne, Sydney, Brisbane, Adelaide and Perth serve makers who need specific veneer or cabinet-grade panels. Australian mains power is 240 V, and workshop drills use Australian three-pin plugs; US 120 V machines will not run directly on that supply. Check that a drill press or sharpener is rated for 240 V and properly insulated, or use a qualified technician for changes. Sloan’s Woodshop is a US-based catalogue that ships within the United States and lists prices in US dollars. Its toll-free ordering line is designed for North American customers, so Australian shoppers should not assume international checkout or a simple return journey. A direct purchase may attract GST, import duty, brokerage and courier charges, making a local purchase often the cheaper and simpler route. Wood packing presents a separate customs issue: imported timber packaging should carry ISPM 15 treatment, and Australian biosecurity rules may apply to timber articles. An unrelated search result, such as a European blackjack guide, contains no useful evidence about drill geometry, so rely instead on manufacturer dimensions, retailer specifications and a test cut in the intended plywood. Diagnosing rough or misaligned holesA wandering hole usually has three causes: the point was not fully engaged, the workpiece moved, or the drill was held at the wrong angle. On a drill press, check the jig and square first. On a handheld drill, reset the tool against the guide rather than forcing the bit along the marked line. Tear-out around the exit face points to speed, feed or support problems. Reduce spindle speed, ease the drill through the final veneer and use a firm backing board. If the entry tears outward, clamp more securely and make sure the mark is on solid wood rather than a hollow gap between panels. Rough walls suggest a blunt bit, heat damage or an oversized hole. Clean chips from the flutes, sharpen or replace the bit and let it cool between repeated passes. Test holes across the full panel stack because veneers and glue lines can change the cut. Using angled holes in finished plywood workAngled holes become useful in compound assemblies, dowel frames and panels that receive knobs, handles or cabinet hardware. Drill mating parts while they are still easy to register, mark the hole axis on both faces with a fine square, and make a test assembly before drilling every joint. Registration tape can prevent the faces from shifting while the first pilot holes are made. The same method works for decorative routing templates, clock cases and laminated panels. If a hole passes through several sheets, identify the face that must remain visible, place that face toward a clean waste board and cut from the less important side when geometry allows. This is particularly valuable with figured face veneers, which show every chipped fibre. Finally, clean chips from the bit after use and store brad points in a case rather than loose in a drawer. A dull point should be replaced before it damages another panel. With a fresh bit, a rigid jig and a firm backing surface, angled holes become a repeatable woodworking operation rather than a test of luck. |
|
Home Plywood Scroll Saw Blades Band Saw Blades Drill Bits Forstner Bits Router Bits Clocks Acrylic Sheets Pattern Books Misc Drum Sander Kit Scroll Sanders & Files Brush Sets Needle File & Riffler Sets Web Specials Scroll Saw Patterns Contact Us Ordering Order Toll Free: 1-888-615-9663 Sloan's Woodshop - 3453 Callis Road - Lebanon, TN 37090 We Do Not Ship Outside of the US |