Sloan's Woodshop - The Scroll Saw Store |
Using a slow-speed drill press attachment with acrylicAcrylic is attractive for clock faces, display pieces, signs, light diffusers and scroll-saw projects because it is light, colourful and easy to shape. It is also less forgiving than timber when a drill bit spins too quickly. Excess heat can soften the hole, melt chips onto the work, or create a web of cracks around the opening. A slow-speed attachment for a drill press helps control that heat. It reduces spindle speed while retaining the steady vertical movement that makes a drill press useful. The arrangement is especially helpful when drilling larger holes, repeated openings or close-to-edge holes in cast or extruded acrylic sheet. Australian makers need to account for metric sizing, 240-volt workshop equipment and warm conditions that can make plastic heat up quickly. A project in Brisbane or Perth during a hot afternoon may need a gentler feed and more frequent pauses than the same job in a cool Tasmanian shed. The method is straightforward when the sheet is supported, the tooling is sharp and the speed is selected for the diameter of the hole. Planning the material, backing board and clamping arrangement before switching on will produce cleaner results than trying to correct a melted or chipped hole afterwards. Why slower speed matters for acrylicAcrylic does not carry heat away as effectively as steel or aluminium. A fast drill bit rubs against the plastic, creating friction faster than the material can dissipate it. The surface may become gummy, the flutes can clog and the hole can taper or distort as the softened edge grabs the tool. A speed reducer, pulley attachment or geared slow-speed unit lowers the spindle revolutions per minute. This gives the cutting edges time to remove chips rather than simply burnish the wall of the hole. The benefit is greatest with larger bits, hole saws and Forstner-style cutters, which generate considerable heat at their outer edges. The reduction attachment must be compatible with the drill press. Check the manufacturer’s permitted spindle speed, belt arrangement, chuck capacity and guard requirements before fitting it. Some compact bench presses are designed for a limited range, while others can be adjusted through pulley steps without an additional attachment. Disconnect power before changing belts or pulleys, and remember that Australian 240-volt equipment requires sound plugs, leads and earthing. Preparing the sheet and drill pressLeave the protective film on both faces of the acrylic while marking and drilling. It helps prevent scratches and makes it easier to draw centre lines. Mark the position with a fine felt-tip pen or place masking tape over the area and mark the tape. A sharp awl can create a starting dimple, but do not strike it hard enough to stress the sheet. Clamp the acrylic firmly over a flat sacrificial board, such as clean MDF or plywood. The backing board supports the underside as the bit exits, reducing breakout and preventing the sheet from lifting into the bit. Never rely on hand pressure alone. A loose sheet can rotate suddenly, crack at the hole or pull fingers towards the cutter. Choose a sharp bit intended for plastics where possible. Standard twist drills may be used if their cutting edges are honed and their rake is not overly aggressive. A bit that bites too deeply can grab the acrylic. For larger openings, a hole saw with fine teeth or a specialist plastic-cutting cutter is preferable. Remove burrs from the hole with a countersink turned by hand rather than using high speed. For specialist blades, drill bits, sanding supplies and acrylic sheets, the Sloan’s Woodshop catalogue is useful when assembling a mixed woodworking order. The retailer also assists customers by phone, which can help when a project needs a particular size or style of cutter. Choosing speed, feed and lubricationThere is no single spindle setting for every acrylic job. Bit diameter, acrylic type, sheet thickness and the sharpness of the cutting edge all affect the result. Begin at the slowest practical setting, make a test hole in an offcut and inspect the chips. Clear, loose chips and a cool edge indicate better cutting; melted ribbons or a sticky rim indicate too much heat. The following starting points are deliberately conservative. They are intended for ordinary cast or extruded acrylic sheet, not glass-filled plastic or other engineering materials. The drill press manual and tool maker’s instructions take priority.
Feed pressure should be firm enough to let the cutting edge work, but never so heavy that the drill press bogs down. A pecking action is useful: lower the bit a short distance, raise it to release chips, then continue. With a deep hole, withdraw the cutter several times rather than forcing all the swarf through the flutes. Water can be used sparingly as a coolant if the drill press and surrounding electrical equipment are protected, but it is not essential for many small holes. A mist of clean water or a little diluted dishwashing liquid may reduce friction, though the sheet should be dried promptly. Avoid petroleum solvents, methylated spirits and incompatible sprays, as they can attack acrylic or cause stress cracking. Drilling clean holes without cracksSet the table square to the spindle and align the marked centre directly beneath the bit. Bring the cutter down slowly until it just touches the film, then begin the cut with controlled pressure. If the bit wanders, stop and correct the setup rather than pushing harder. A pilot hole can guide a larger cutter, provided the pilot is straight and does not create a sharp stress point. As the bit approaches the backing board, reduce pressure. Breakout commonly occurs when the last thin layer of acrylic is pushed away instead of cut. For a critical visible face, drill part-way from one side, turn the sheet over using the centre marks, and finish from the reverse. This produces clean edges on both faces when the alignment is accurate. Stop if the acrylic begins to whiten, craze or smell strongly of hot plastic. Those signs suggest excessive heat, a dull tool or excessive feed. Let the sheet cool naturally, inspect the cutter and make another test. Do not quench a hot sheet with cold water, because a sudden temperature change can add stress and cause cracking. The risk of a poor result increases when several variables are changed at once. Alter one factor at a time—speed, feed, bit condition or cooling—so the test hole tells you what actually helped. This measured approach resembles the basic principle in a casino odds guide: understand the risk before committing resources, rather than relying on a lucky result. Finishing the project and storing acrylicAfter drilling, leave the protective film in place while removing the sheet from the press. Pick away loose swarf rather than wiping hot chips across the surface. A deburring tool, fine file or hand-turned countersink will soften the rim. For a clock insert or washer, test the fit gradually; forcing a tight component into an undersized hole can split the acrylic later. Clean the finished piece with mild soapy water and a soft microfibre cloth. Paper towels can leave fine scratches, while ammonia-based glass cleaners may damage or craze some acrylic products. If adhesive is required, use a product specifically rated for acrylic and test it on an offcut first. Store unused sheets flat on a clean, level surface away from direct sunlight and heaters. Australian sheds can become extremely hot, particularly in western suburbs and inland towns, so avoid leaning thin sheets against a corrugated wall or leaving them in a closed ute. Keep the protective film on until cutting, drilling, sanding and assembly are complete. For projects ordered from Australian suppliers, check the sheet dimensions, thickness and delivery conditions before choosing the drill setting. Imported metric stock can vary slightly from local descriptions, and freight across Australia may expose a large sheet to bending or heat. A flat, undamaged starting piece makes accurate drilling much easier. With a compatible slow-speed setup, sharp tooling and a supportive backing board, acrylic can be drilled cleanly and repeatedly. The key is to remove heat with controlled cutting rather than trying to solve the problem after the edge has softened. Test on scrap, work in metric sizes and let the material’s chips and surface finish guide the final adjustment. |
|
Home Plywood Scroll Saw Blades Band Saw Blades Drill Bits Forstner Bits Router Bits Clocks Acrylic Sheets Pattern Books Misc Drum Sander Kit Scroll Sanders & Files Brush Sets Needle File & Riffler Sets Web Specials Scroll Saw Patterns Contact Us Ordering Order Toll Free: 1-888-615-9663 Sloan's Woodshop - 3453 Callis Road - Lebanon, TN 37090 We Do Not Ship Outside of the US |